Download CCNA Collaboration Implementing Cisco Video Network Devices (CIVND).testkings.210-065.2019-01-30.1e.235q.vcex

In this item, you will need to use all information presented to you to successfully answer the question. 

• A: The subnet mask on the codec is incorrect.
• B: The ip address of the codec is incorrect.
• C: The interface that the codec is in is in the wrong VLAN.
• D: The codec did not receive a DHCP address from the DHCP server.

Correct Answer: A

Which three of these are functions of the Cisco TelePresence Management Suite? (Choose three.)

• A: automatic software update and release keys
• B: intelligent call routing engine
• C: provisioning a Cisco TelePresence System endpoint
• D: tracing SIP and H.323 calls
• E: managing phonebooks for endpoints that are registered to the Cisco Unified Cisco Unified Communications Manager
• F: rebooting endpoints that are registered to the Cisco TelePresence Video Communications Server

Correct Answer: ABF

Refer to the exhibit. 

• A: Navigator
• B: System Overview
• C: Configuration Templates
• D: Provisioning
• E: Administrative Tools

Correct Answer: A

Section 1 - Basic Endpoint configuration 
Step 1 - Prior to setting up the traversal zone you will need to get all of your endpoints registered to your video network. There are several ways to do this for simplicity we will walk you through just one option. 
a. On your lab laptop open a web browser and navigate to your Telepresence Management Suite (TMS) instance at: http://tms.collab.com/tms
b. Login as 

  

  

Figure 1 TMS Login 
Step 2 -Navigate to Systems → Navigator (Figure 1) 
Step 3 - Click the "Endpoints" folder on the left side of the window and click "add systems" as depicted below in Figure 2 

  

Figure 2 Adding Endpoints 
Step 4 - Enter the IP address of your C60, and the EX60 that is not registered to CUCM into the Specify Systems text field, separating each with a comma as depicted in Figure 3below. 
Make sure that you: Leave the ISDN and IP zones "Collab Demo"
Ensure that the time zone is set to "Eastern" 
You can find the IP address of your EX60s via the system information screen on the touch panel. 
For the C60 press the home key then the far right smart button to bring up your System information screen. 

  

Figure 3 Adding Endpoints to TMS 
Step 5 - Click next, a progress window will appear as TMS reaches out to each endpoint. Once completed you see the "Add Result" screen showing that the endpoints were successfully discovered. 
Step 6 - Finally click "Finish Adding Systems" as depicted in Figure 4. 
NOTE: If your endpoints throw warnings click the check box next to them to view and correct the warnings or click "Add system despite Warnings" if available

  

Reference: http://ciscovideolab.com/mediawiki/index.php?title=Lab1
http://www.cisco.com/c/dam/en/us/td/docs/telepresence/infrastructure/tms/admin_guide/Cisco-TMS-Admin-Guide-14-6.pdf

Which two layout or switching modes are supported with the Cisco TelePresence Multipoint Switch? (Choose two.)

• A: enhanced continuous presence
• B: active speaker switching
• C: continuous presence
• D: speaker switching
• E: room switching
• F: active continuous presence

Correct Answer: DE

Switching policy: Two types of switching policy are available:
◦     Room switching: Room switching switches the video from all table segments of a room to all other rooms in a meeting. If the active speaker (loudest speaker for approximately 2 seconds) changes, all table segments in the new active speaker's room will be displayed in all other rooms at the same time, replacing the previously active room.
◦     Speaker switching: Speaker switching allows each segment to be switched independently, so that at any given time the three active segments, in one or multiple rooms, are displayed in all Cisco TelePresence rooms. If the active speaker changes, the speaker's table segment will be displayed in all other rooms on the corresponding screen, as shown in Figure 2.
Figure 2.      Room and Speaker Switching 

  

Reference: http://www.cisco.com/c/en/us/products/collateral/conferencing/telepresence-multipoint-switch/white_paper_c11-610159.html

Which Cisco TelePresence Multipoint Control Unit Layout view mode gives prominence to one conference participant over the other conference participants while still allowing conference participants to view multiple participants at the same time?

• A: enhanced continuous presence
• B: active speaker
• C: continuous presence
• D: room switching
• E: speaker switching

Correct Answer: A

An important Cisco TelePresence video multipoint call is in progress and you are getting complaints of pixilation of the video and poor audio quality on one of the involved systems. Which page would be a good place to start for troubleshooting the issue on the affected endpoint?

• A:
  
    
• B:
  
    
• C:
  
    
• D:
  
    

Correct Answer: A

Which two of these support an ad-hoc conference call? (Choose two.)

• A: Cisco TelePresence Multiway with Cisco TelePresence Multipoint Control Unit and Cisco TelePresence Video Communications Server
• B: using the Cisco TelePresence Management Suite Scheduler to schedule a conference call to start in 5 minutes
• C: using the Booking tab in the Cisco TelePresence Management Suite to configure a new conference
• D: using the tab Administrative Tools > Configuration > Conference Settings in the Cisco TelePresence Management Suite
• E: pressing the conference button on a Cisco Unified IP Phone 8941 to conference in a third call

Correct Answer: AE

Multiway system requirements 
Your deployment must have the following components:

  Cisco TelePresence endpoints that support Multiway™ 

  Cisco TelePresence Video Communication Server (VCS) 

  Cisco TelePresence MCU 
E: http://www.cisco.com/c/dam/en/us/td/docs/voice_ip_comm/cuipph/8941_8945/8_5/english/qsg/QSG_8941_8945_en_851.pdf

  

Reference:
http://www.cisco.com/c/en/us/td/docs/telepresence/infrastructure/articles/cisco_telepresence_mcu_configure_multiway_kb_166.html

Refer to the exhibit. 

• A: Conference 1
• B: NetworkServices
• C: Provisioning
• D: SIP Profile 1
• E: Video

Correct Answer: B

  

http://www.cisco.com/c/dam/en/us/td/docs/telepresence/infrastructure/vcs/config_guide/Cisco_VCS_Multiway_Deployment_Guide_X6.pdf

Refer to the exhibit. 

• A: Diagnostics
• B: Configuration
• C: Call Control
• D: Maintenance
• E: The GUI cannot be used to view call statistics.

Correct Answer: C

Which function does a Cisco TCS recording alias perform?

• A: It links recorded media to a specified output location.
• B: It provides a dialable alias that will trigger a TCS recording workflow.
• C: It sends media to Cisco Medianet.
• D: It provides an alias for the recorded filename.

Correct Answer: B