Download Implementing Cisco IP Switched Networks (SWITCH v2-0).actualtests.300-115.2018-08-08.1e.302q.vcex

Download Exam

File Info

Exam Implementing Cisco IP Switched Networks (SWITCH v2.0)
Number 300-115
File Name Implementing Cisco IP Switched Networks (SWITCH v2-0).actualtests.300-115.2018-08-08.1e.302q.vcex
Size 7.91 Mb
Posted August 08, 2018
Downloads 142
Download Implementing Cisco IP Switched Networks (SWITCH v2-0).actualtests.300-115.2018-08-08.1e.302q.vcex

How to open VCEX & EXAM Files?

Files with VCEX & EXAM extensions can be opened by ProfExam Simulator.

Purchase

Coupon: MASTEREXAM
With discount: 20%



 
 



Demo Questions

Question 1

Which of the following commands can be issued without interfering with the operation of loop guard?

  • A: Switch(config-if)#spanning-tree guard root
  • B: Switch(config-if)#spanning-tree portfast
  • C: Switch(config-if)#switchport mode trunk
  • D: Switch(config-if)#switchport mode access

Correct Answer: C




Question 2

The following command was issued on a router that is being configured as the active HSRP router. 
standby ip 10.2.1.1 
Which statement is true about this command?

  • A: This command will not work because the HSRP group information is missing
  • B: The HSRP MAC address will be 0000 0c07 ac00
  • C: The HSRP MAC address will be 0000 0c07 ac01.
  • D: The HSRP MAC address will be 0000.070c ad01.
  • E: This command will not work because the active parameter is missing

Correct Answer: B




Question 3

Routers R1 and R2 are configured for HSRP as shown below:
Router R1:
interface ethernet 0 
ip address 20.6.2.1 255.255.255.0 
standby 35 ip 20.6.2.21 
standby 35 priority 100 
interface ethernet 1 
ip address 20.6.1.1.2 255.255.255.0 
standby 34 ip 20.6.1.21 
Router R2:
interface ethernet 0 
ip address 20.6.2.2 255.255.255.0 
standby 35 ip 20.6.2.21 
interface ethernet 1 
ip address 20.6.1.1.1 255.255.255.0 
standby 34 ip 20.6.1.21 
standby 34 priority 100 
You have configured the routers R1 & R2 with HSRP. While debugging router R2 you notice very frequent HSRP group state transitions. What is the most likely cause of this?

  • A: physical layer issues
  • B: no spanning tree loops
  • C: use of non-default HSRP timers
  • D: failure to set the command standby 35 preempt

Correct Answer: A




Question 4

Which two statements about the HSRP priority are true? (Choose two.)

  • A: To assign the HSRP router priority in a standby group, the standby group-number priority priority-value global configuration command must be used.
  • B: The default priority of a router is zero (0).
  • C: The no standby priority command assigns a priority of 100 to the router.
  • D: Assuming that preempting has also been configured, the router with the lowest priority in an HSRP group would become the active router.
  • E: When two routers in an HSRP standby group are configured with identical priorities, the router with the highest configured IP address will become the active router.

Correct Answer: CE




Question 5

Which three statements are true of a default HSRP configuration? (Choose three.)

  • A: The Standby hello time is 2 seconds.
  • B: Two HSRP groups are configured.
  • C: The Standby track interface priority decrement is 10.
  • D: The Standby hold time is 10 seconds
  • E: The Standby priority is 100.
  • F: The Standby delay is 3 seconds.

Correct Answer: CDE




Question 6

Refer to the exhibit. What is the result of setting GLBP weighting at 105 with lower threshold 90 and upper threshold 100 on this router? 

 

  

  • A: Only if both tracked objects are up will this router will be available as an AVF for group 1.
  • B: Only if the state of both tracked objects goes down will this router release its status as an AVF for group 1.
  • C: If both tracked objects go down and then one comes up, but the other remains down, this router will be available as an AVF for group 1.
  • D: This configuration is incorrect and will not have any effect on GLBP operation.
  • E: If the state of one tracked object goes down, then this router will release its status as an AVF for group 1.

Correct Answer: B




Question 7

Which describes the default load balancing scheme used by the Gateway Load Balancing Protocol (GLBP)?

  • A: Per host using a strict priority scheme
  • B: Per session using a round-robin scheme
  • C: Per session using a strict priority scheme
  • D: Per GLBP group using a strict priority scheme
  • E: Per host basis using a round robin-scheme
  • F: Per GLBP group using a round-robin scheme

Correct Answer: E




Question 8

Which two statements about default FHRP behavior are true? (Choose two.)

  • A: A backup GLBP active virtual gateway can become active only if the current active virtual gateway fails.
  • B: Preemption is enabled by default.
  • C: Unless specifically Configured, the priority of an HSRP router is 200.
  • D: A standby HSRP router becomes active if it has a higher priority than the priority of the current active router.
  • E: A VRRP backup virtual router becomes the master router if its priority is higher than the priority of the current master router.

Correct Answer: AE




Question 9

To provide security, a service provider configures various private VLANs in its backbone network infrastructure to prevent certain VLANs from communicating to each other. 
Which version of VTP supports the use of private VLANs?

  • A: Version 1
  • B: Version 3
  • C: VTP does not support private VLANs
  • D: Version 2

Correct Answer: B




Question 10

Which statement about HSRP, GLBP, and VRRP is true?

  • A: VRRP group members communicate using multicast address 224.0.0.102.
  • B: MAC address 0000.0c07.acOc indicates that default gateway redundancy is provided through GLBP.
  • C: HSRP group members communicate using multicast address 224.0.0.18.
  • D: GLBP uses UDP port 3222 (source and destination) for hello messages.
  • E: MAC address 0c07.A698.8904 indicates that default gateway redundancy is provided through HSRP.

Correct Answer: D










CONNECT US

Facebook

Twitter

PROFEXAM WITH A 20% DISCOUNT

You can buy ProfExam with a 20% discount!



HOW TO OPEN VCEX AND EXAM FILES

Use ProfExam Simulator to open VCEX and EXAM files