File Info
| Exam | Implementing Cisco IP Switched Networks (SWITCH v2.0) |
| Number | 300-115 |
| File Name | Implementing Cisco IP Switched Networks (SWITCH v2-0).prep4sure.300-115.2018-09-10.1e.351q.vcex |
| Size | 6.81 Mb |
| Posted | September 10, 2018 |
| Downloads | 196 |
| Download | Implementing Cisco IP Switched Networks (SWITCH v2-0).prep4sure.300-115.2018-09-10.1e.351q.vcex |
How to open VCEX & EXAM Files?
Files with VCEX & EXAM extensions can be opened by ProfExam Simulator.
Coupon: MASTEREXAM
With discount: 20%
Demo Questions
An engineer is configuring an EtherChannel between two switches using LACP. If the EtherChannel mode on switch 1 is configured to active, which two modes on switch 2 establish an operational EtherChannel? (Choose two.)
- A: active
- B: auto
- C: desirable
- D: on
- E: passive
Correct Answer: AE
When a Layer 2 EtherChannel is configured, which statement about placement of the IP address is true?
- A: The IP address is placed on the highest numbered member port.
- B: The IP address is placed on the port-channel logical interface.
- C: The IP address is placed on the lowest numbered member port.
- D: The IP address is assigned via DHCP only.
Correct Answer: B
Which option is valid for EtherChannel load balancing?
- A: source MAC address and source IP address
- B: destination MAC address and destination IP address
- C: source MAC address and destination IP address
- D: source MAC address and destination MAC address
Correct Answer: D
Refer to the exhibit.
An engineer is configuring EtherChannel between two switches and notices the console message on switch 2. Based on the output, which option describes the reason for this error?
- A: Switch 1 does not have enough member ports configured.
- B: Switch 2 has too many member ports configured.
- C: The port channel interface numbers do not match.
- D: The EtherChannel protocols do not match.
Correct Answer: D
Refer to the exhibit.
DSW1 should share the same MST region with switch DSW2. Which statement is true?
- A: Configure DSW1 with the same version number, and VLAN-to-instance mapping as shown on DSW2.
- B: DSW2 uses the VTP server mode to automatically propagate the MST configuration to DSW1.
- C: DSW1 automatically inherits MST configuration from DSW2 because they have the same domain name.
- D: Configure DSW1 with the same region name, revision number, and VLAN-to-instance mapping as shown on DSW2.
- E: DSW1 is in VTP client mode with a lower configuration revision number, therefore, it automatically inherits MST configuration from DW2.
Correct Answer: D
Which two statements about SPAN source and destination ports during an active session are true? (Choose two.)
- A: The source port can be only an Ethernet physical port.
- B: The source port can be monitored in multiple SPAN sessions.
- C: The destination port can be destination in multiple SPAN sessions.
- D: The destination port does not participate in STP.
- E: You can mix individual source ports and source VLANs within a single session.
Correct Answer: BD
In a switch stack environment, what is the total bidirectional traffic flow between two logical counter-rotating paths?
- A: 16 Gbps
- B: 32 Gbps
- C: 64 Gbps
- D: 128 Gbps
Correct Answer: B
Refer to the exhibit.
Which statement about the SPAN and RSPAN configuration on SW1 is true?
- A: SPAN session 2 only monitors egress traffic exiting port FastEthernet 0/14.
- B: RSPAN session 1 monitors activity on VLAN 50 of a remote switch.
- C: RSPAN session 1 is incompletely configured for monitoring.
- D: SPAN session 2 monitors all traffic entering and exiting port FastEthernet 0/15.
Correct Answer: C
Which option is the minimum number of bindings that the DHCP snooping database can store?
- A: 1000 bindings
- B: 2000 bindings
- C: 5000 bindings
- D: 8000 bindings
Correct Answer: D
On which layer does IP source guard provide filtering to prevent a malicious host from impersonating the IP address of a legitimate host?
- A: Layer 1
- B: Layer 2
- C: Layer 3
- D: Layer 7
Correct Answer: B
