Download Cisco.300-410.VCEplus.2021-03-23.114q.tqb

The IPv4 address of the IPv6 router is 208.48.107.192. In an automatic 6-to-4 tunnel, IPv6 addresses have the 2002::/16 prefix. The 32-bit IPv4 address of the IPv6 router is then embedded into the IPv6 address. The 32 bits of the IPv4 address is embedded in the second and third quartet of the IPv6 address. The second and third quarters in the IPv6 address correspond to D030:6BC0. The conversion of these hexadecimal digits into decimal is given as follows:           The IPv6 router does not have 10.176.15.131 as its IPv4 address. The 10.176.15.131 address is the IPv4 equivalent of the second and third quarter (05B0:0F81) in the source IPv6 address.  The other two IPv4 addresses are incorrect as they pertain to neither of the two IPv6 hosts.  Objective: Network   Principles Sub- Objective: Recognize proposed changes to the network  References: Cisco IOS IPv6 Implementation Guide > Implementing Tunneling for IPv6

The correct answer is to use the tunnel mode ipv6ip 6to4 command to complete the configuration of an automatic 6-to-4 tunnel. This command requires the use of IPv6 unicast addresses that have the 2002::/16 prefix. The types of tunneling mechanisms supported by IPv6 are: Automatic 6-to-4 tunnel  ISATAP tunnel  Manually configured tunnel  GRE tunnel   Apart from using a tunneling mechanism, interoperability between IPv4 and IPv6 can be provided by using a dual-stack infrastructure or Network Address Translation-Protocol Translation (NAT-PT). A dual-stack infrastructure allows you to use both IPv4 and IPv6 addresses on the same router/host. NAT-PT is used to translate IPv4 addresses to IPv6 and vice versa.  The tunnel mode ipv6ip command should not be used to complete the configuration because this command specifies IPv6 as the passenger protocol and creates a manually configured tunnel.  The tunnel mode ipv6ip auto-tunnel command is not required to enable automatic 6-to-4 tunneling on the border routers. This command creates an automatic IPv4compatible IPv6 tunnel between the routers.  The tunnel mode ipv6ip isatap command should not be used because this command creates an ISATAP tunnel.  Objective: Network  Principles Sub- Objective: Recognize proposed changes to the network  References: Cisco IOS IPv6 Configuration Guide; Implementing Tunneling for IPv6 > Configuring Manual IPv6 Tunnels Cisco > Cisco IOS IPv6 Command Reference > tunnel mode ipv6ip   

The 2002:c0a8:4b01::1/64 and the 2002:c0a8:7d01::1/64 IPv6 addresses should be assigned to the Fa0/1 interfaces of rtrB and rtrC, respectively. Automatic 6-to-4 tunnels embed the IPv4 address of the tunnel interfaces into the second and third quartets of the IPv6 address that has the 2002::/16 prefix. To assign IPv6 addresses to the tunnel interfaces, perform the following steps: Convert the IPv4 address of the tunnel interface into binary.  Convert the binary equivalent of the IPv4 address into hexadecimal (IPv6).  Append the hexadecimal equivalent to the 2002::/16 prefix to form the IPv6 prefix of the tunnel interface.  For the Fa0/1 interface of rtrB, its IPv4 address of 192.68.75.1 is equivalent to the IPv6 address c0a8:4b01. This address is then appended to the 2002::/16 prefix, resulting in 2002:c0a8:4b01::/48. The remaining host bits can be filled with zeros. Similarly, the IPv4 address of the Fa0/1 interface of rtrC is converted to the IPv6 address 2002:c0a8:7d01::/48. The 2002::c0a8:2d01/64 IPv6 address should not be assigned to the Fa0/1 interface of rtrA. The Fa0/1 interface of rtrA has the IPv4 address 192.168.45.1. The IPv6 equivalent of the IPv4 address, which is c0a8:2d01, should be embedded in the second and third quartets of the IPv6 address instead of the seventh and eighth quartets. IPv4 addresses are embedded into the last 32 bits for ISATAP tunnels.  The 2002:c0a8:4b01::1/64 IPv6 addresses should not be assigned to the Fa0/1 interface of rtrA. This IPv6 address is the equivalent of the IPv4 address 192.168.75.1, which is the address of the Fa0/2 interface of rtrB and not rtrA. Therefore, this IPv6 address should be assigned to the Fa0/1 interface of rtrB.  Objective: Network  Principles Sub- Objective: Recognize proposed changes to the network  References: Cisco Press > Articles > Cisco Certification > CCNP > CCNP Self-Study: Advanced IP Addressing Cisco Press > Articles > Network Technology > General Networking > Cisco Self-Study: Implementing Cisco IPv6 Networks (IPV6) Cisco > Support > Technology Support > IP > IP Version 6 (IPV6) > Configure > Configuration Examples and Technotes > IPv6 Tunnel Through an IPv4 Network  Cisco IOS IPv6 Implementation Guide, Release 15.2M&T > Implementing Tunneling for IPv6