Download Implementing Cisco Enterprise Advanced Routing and Services (300-410 ENARSI).Marks4Sure.300-410.2021-03-22.1e.71q.vcex

Download Exam

File Info

Exam Implementing Cisco Enterprise Advanced Routing and Services (300-410 ENARSI)
Number 300-410
File Name Implementing Cisco Enterprise Advanced Routing and Services (300-410 ENARSI).Marks4Sure.300-410.2021-03-22.1e.71q.vcex
Size 9.35 Mb
Posted March 22, 2021
Downloads 22
Download Implementing Cisco Enterprise Advanced Routing and Services (300-410 ENARSI).Marks4Sure.300-410.2021-03-22.1e.71q.vcex

How to open VCEX & EXAM Files?

Files with VCEX & EXAM extensions can be opened by ProfExam Simulator.


With discount: 20%


Demo Questions

Question 1

Refer to the exhibit.  


Users in the branch network of 2001:db8:0:4::/64 report that they cannot access the Internet. Which command is issued in IPv6 router EIGRP 100 configuration mode to solve this issue?

  • A: Issue the eigrp stub command on R1.
  • B: Issue the no eigrp stub command on R1
  • C: Issue the eigrp stub command on R2.
  • D: Issue the no eigrp stub command on R2.

Correct Answer: B

Question 2

Refer to the exhibit. 


An engineer configures a static route on a router, but when the engineer checks the route to the destination, a different next hop is chosen. What is the reason for this?  

  • A: Dynamic routing protocols always have priority over static routes.
  • B: The metric of the OSPF route is lower than the metric of the static route.
  • C: The configured AD for the static route is higher than the AD of OSPF.
  • D: The syntax of the static route is not valid, so the route is not considered.

Correct Answer: C

The AD of static route is manually configured to 130 which is higher than the AD of OSPF router which is 110.

Question 3

Drag and drop the DHCP messages from the left onto the correct uses on the right.  

Correct Answer: Exam simulator is required

The server-to-client communication with configuration parameters, including committed network address. 
The client-to-server communication, asking for only local configuration parameters that the client already has externally configured as an address. 
The server-to-client communication, refusing the request for configuration parameter. 
The client-to-server communication, indicating that the network address is already in use 

Question 4

Which IGPs are supported by the MPLS LDP autoconfiguration feature?

  • A: RIPv2 and OSPF
  • B: OSPF and EIGRP
  • C: OSPF and ISIS
  • D: ISIS and RIPv2

Correct Answer: C

Question 5

When provisioning a device in Cisco DNA Center, the engineer sees the error message “Cannot select the device. Not compatible with template”. 
What is the reason for the error?

  • A: The template has an incorrect configuration.
  • B: The software version of the template is different from the software version of the device.
  • C: The changes to the template were not committed.
  • D: The tag that was used to filter the templates does not match the device tag.

Correct Answer: D

If you use tags to filter the templates, you must apply the same tags to the device to which you want to apply the templates. Otherwise, you get the following error during provisioning: Cannot select the device. Not compatible with template.

Question 6

Which component of MPLS VPNs is used to extend the IP address so that an engineer is able to identify to which VPN it belongs?

  • A: VPNv4 address family
  • B: RD
  • C: RT
  • D: LDP

Correct Answer: B

Question 7

An engineer needs dynamic routing between two routers and is unable to establish OSPF adjacency. The output of the show ip ospf neighbor command shows that the neighbor state is EXSTART/EXCHANGE. 
Which action should be taken to resolve this issue?

  • A: match the passwords
  • B: match the hello timers
  • C: match the MTUs
  • D: match the network types

Correct Answer: C

Question 8



BGP is flapping after the Copp policy is applied. What are the two solutions to fix the issue? (Choose two)

  • A: Configure BGP in the COPP-CRITICAL-7600 ACL
  • B: Configure a higher value for CIR under the default class to allow more packets during peak traffic
  • C: Configure a higher value for CIR under the class COPP-CRITICAL-7600
  • D: Configure a three-color policer instead of two-color policer under class COPP-CRITICAL-7600
  • E: Configure IP CEF to CoPP policy and BGP to work 

Correct Answer: AB

The policy-map COPP-7600 only rate-limit HTTP & HTTPS traffic (based on the ACL conditions) so any BGP packets will be processed in the class “class-default”, which drops exceeded BGP packets. Therefore we have two ways to solve this problem:
Add BGP to the ACL with the statement “permit tcp any any eq bgp” 
Configure higher value for CIR in default class as 2Mbps is too low for web traffic (http & https)

Question 9

A network engineer needs to verify IP SLA operations on an interface that shows on indication of excessive traffic. 
Which command should the engineer use to complete this action?

  • A: show frequency
  • B: show track   
  • C: show reachability
  • D: show threshold

Correct Answer: B

Question 10

An engineer is configuring a network and needs packets to be forwarded to an interface for any destination address that is not in the routing table. What should be configured to accomplish this task?

  • A: set ip next-hop
  • B: set ip default next-hop
  • C: set ip next-hop recursive
  • D: set ip next-hop verify-availability

Correct Answer: B





You can buy ProfExam with a 20% discount!


Use ProfExam Simulator to open VCEX and EXAM files