File Info
| Exam | Implementing Cisco Enterprise Wireless Networks (300-430 ENWLSI) |
| Number | 300-430 |
| File Name | Cisco.300-430.CertDumps.2024-08-23.216q.tqb |
| Size | 6 MB |
| Posted | Aug 23, 2024 |
| Download | Cisco.300-430.CertDumps.2024-08-23.216q.tqb |
How to open VCEX & EXAM Files?
Files with VCEX & EXAM extensions can be opened by ProfExam Simulator.
Coupon: MASTEREXAM
With discount: 20%
Demo Questions
Question 1
Which command set configures a Cisco Catalyst 9800 Series Wireless Controller so that the client traffic enters the network at the AP switch port?
Correct answer: D
Question 2
Refer to the exhibit.
An engineer must provide a position of rogue APs on a floor map using Cisco PI 3.0, but no rogue AP options are showing on the left-hand navigation menu under Maps. What is the reason for this omission?
- An assurance license is not installed.
- The controller operational status background task is disabled.
- The Show Detected Interferers feature under the AP option is disabled.
- Cisco MSE has not been added to Cisco PI.
Correct answer: A
Question 3
Refer to the exhibit.
An engineer needs to configure location services in an office. The requirement is to use FastLocate and achieve higher locations refresh rates. Which location-based technique should be implemented?
- probe-based
- location patterning
- data packet-based
- angulation
Correct answer: C
Question 4
You enter the command or a Cisco Catalyst 3850 Series Switch that runs Cisco ISO XE.
What does the command do?
- It defines the user identity or the device identity to be validated by the RADIUS server.
- It captures information on the length of the authorized session, as well as the bandwidthusage of the client.
- It defines the RADIUS server used to track which sessions are still active.
- It defines the level of access of the user or the device.
Correct answer: D
Question 5
What is the Cisco recommended configuration for a Cisco switch port connected to an AP in local mode for optimal voice over WLAN performance with an 8821 wireless phone?
- switchport encapsulation dot1qswitchport mode trunk mls qos trust device cisco-phone
- switchport mode accessmls qos trust device cisco-phone
- switchport mode access mls qos trust cos
- switchport mode access mls qos trust dscp
Correct answer: C
Question 6
During the EAP process and specifically related to the client authentication session, which encrypted key is sent from the RADIUS server to the access point?
- WPA key
- session key
- encryption key
- shared-secret key
Correct answer: B
Question 7
A corporation has employees working from their homes. A wireless engineer must connect 1810 OEAP at remote teleworker locations. All configuration has been completed on the controller side, but the network readiness is pending. Which two configurations must be performed on the firewall to allow the AP to join the controller? (Choose two.)
- Block UDP ports 1812 and 1813 on the firewall.
- Enable NAT Address on the 5520 with an Internet-routable IP address.
- Configure a static IP on the OEAP 1810.
- Allow UDP ports 5246 and UDP port 5247 on the firewall.
- Allow UDP ports 12222 and 12223 on the firewall.
Correct answer: BD
Question 8
Refer to the exhibit.
An ACL is configured to restrict access for BYOD clients. The ACL must redirect devices to the guest portal. To which two devices on the local network must the ACL allow access other than the DHCP server? (Choose two.)
- RADIUS server
- DNS server
- Cisco ISE
- SNMP server
- WLC
Correct answer: BC
Question 9
Refer to the exhibit.
A customer has implemented Cisco FlexConnect deployments with different WLANs around the globe and is opening a new branch in a different location. The engineer's task is to execute all the wireless configuration and to suggest how to configure the switch ports for new APs. Which configuration must the switching team use on the switch port?
- trunk mode
- access mode
- single VLAN
- multiple VLAN
Correct answer: A
Question 10
A wireless network has been implemented to enable multicast video to be streamed reliably over the wireless link to the wireless users. After a client reports that the video is unable to stream, the administrator determines that the client is connecting at a data rate of 12 Mbps and is trying to stream to a valid multicast address on the network. Which two actions must be applied? (Choose two.)
- Turn off IGMP snooping for all the configured WLANs on the controller.
- Implement video-stream for the multicast video on the controller.
- Allow multicast-direct to work correctly and multicast-direct to be enabled globally.
- Change the WLAN QoS value to Bronze for the WLAN that multicast will be enabled.
- Allow RTSP to stream the video due to wireless multicast not using acknowledgements.
Correct answer: BC
