File Info
| Exam | Troubleshooting Cisco Data Center Infrastructure (DCIT) |
| Number | 300-615 |
| File Name | Cisco.300-615.VCEplus.2024-08-09.93q.vcex |
| Size | 9 MB |
| Posted | Aug 09, 2024 |
| Download | Cisco.300-615.VCEplus.2024-08-09.93q.vcex |
How to open VCEX & EXAM Files?
Files with VCEX & EXAM extensions can be opened by ProfExam Simulator.
Coupon: MASTEREXAM
With discount: 20%
Demo Questions
Question 1
You have an ACI environment with three APICs, two spine switches, and four-leaf switches. You wipe and reboot all APICs first then leaf and spine switches one-by-one and successfully go through the Initial Setuo dialogue on the APIC 1 CIMC KVM console. When you log in to the APIC1 WebGUI, you notice that you do not see any directly connected leaf switches being discovered under Fabric > Inventory > Fabric Membership. What is the cause of the issue?
- The leaf nodes were not erased properly, which caused a fabric parameters mismatch with the APIC1.
- Rebooting the APICs and the leaf and spine switches after wiping them is not required.
- You forgot to enter the TEP Pool value during the Initial Setup dialogue on APIC1.
- The same Fabric Name value should be used before after wiping all devices.
Correct answer: C
Question 2
An engineer must replace a failed memory on a Cisco UCS B-Series Blade Server. After the replacement was done, the server has a "resolve slot" warning. Which server maintenance action resolves the issue?
- Perform diagnostic interrupt on the server.
- Re-acknowlegement the server.
- Reset the server.
- Decomission the server.
Correct answer: B
Question 3
Cisco Unified Computing System Manager raises a critical error message that indicates that the system has overlapping Ethernet and FCoE VLANs. All of the Ethernet traffic on the overlapping VLANs drops. Which action resolves the issue?
- Modify the VLAN assignment to vNICs.
- Change the PIN groups on the vHBAs.
- Modify the FCoE VLAN.
- Set the FCoE VLAN as the native VLAN on server uplinks.
Correct answer: C
Question 4
Refer to the exhibit.
An engineer is performing a health check on ACI. Which statement about interface Ethernet 1/11 is true?
- The interface is working correctly and fully operational, but it is not in use.
- The interface policy is misconfigured.
- "out-of-service" is the default interface status in ACI.
- "out-of-service" indicates that no service graph is in use for this interface.
Correct answer: B
Question 5
A user reports that they cannot reach from a UCS server to an FC Storage array. Which command is used to test communication between an FCF and a target?
- fcroute
- traceroute
- fcping
- ping
Correct answer: C
Question 6
An engineer is implementing a storage VDC, but fails. Which two prerequisites must be in place before a storage VDC is implemented? (Choose two.)
- M-Series module
- ESSENTIALS license
- STORAGE-ENT license
- FCoE license
- F-Series module
Correct answer: DE
Question 7
Refer to the exhibit.
An engineer is troubleshooting why user1, user2, and user3 from group STORAGE- ADMINISTRATOR in Microsoft Active Directory cannot log in to the Cisco MDS SSH CLI. Which action resolves the issue?
- Configure the role name to match the group name on Microsoft Active Directory.
- Include specific users into MDS role configuration.
- Configure SSH logins on Cisco MDS switch.
- Integrate Cisco MDS with Microsoft Active Directory.
Correct answer: A
Question 8
Refer to the exhibit.
An attempt to bind the Ethernet interface to vFC fails. Which action resolves the issue?
- Add the FCoE VLAN to the allowed VLAN list.
- Configure the FCoE VLAN that corresponds to the vFC VSAN as a private VLAN.
- Configure the interface as a trunk port.
- Configure the interface to use the native VLAN of the trunk port.
Correct answer: C
Question 9
Refer to the exhibit.
A new Cisco Nexus 5548 Switch connects to a network. SAN switching is configured on the switch.
The switch fc2/10 NP uplink is shown in the exhibit. Which action ensures that fc2/10 is in an up state?
- Replace the SFP port module in fc2/10.
- Configure the admin port type E on the upstream switch that connects the port.
- Enable NPIV on the upstream switch that connects the port.
- Configure the BB_credit buffers on the upstream switch that connects the port.
Correct answer: C
Question 10
Refer to the exhibit.
The connection between a Cisco Nexus 5548UP switch and a Cisco MDS switch fails to initialize. What is the cause of the issue?
- VSAN 1 is suspended.
- The SFP is unsupported.
- Trunk mode must be activated.
- The interface is in an incorrect mode.
Correct answer: A
