File Info
| Exam | Specialist - Platform Engineer, PowerStore Exam |
| Number | DES-1241 |
| File Name | Dell.DES-1241.PrepAway.2020-11-10.56q.vcex |
| Size | 1 MB |
| Posted | Nov 10, 2020 |
| Download | Dell.DES-1241.PrepAway.2020-11-10.56q.vcex |
How to open VCEX & EXAM Files?
Files with VCEX & EXAM extensions can be opened by ProfExam Simulator.
Coupon: MASTEREXAM
With discount: 20%
Demo Questions
Question 1
What describes Dell EMC PowerStore X front-end cabling?
- Uses internal VMware virtual switching and does not require a management network
- Storage and management use the same LACP bonded cable connection
- Uses VLTi data switch interconnectivity to support vMotion networks
- Management and discovery use the same cables and connections as storage
Correct answer: C
Question 2
Through which network do external hosts connect to the cluster for data access?
- Management
- ICM
- ICD
- Storage
Correct answer: D
Explanation:
Reference: https://topics-cdn.dell.com/pdf/pwrstr-hcg_en-us.pdf Reference: https://topics-cdn.dell.com/pdf/pwrstr-hcg_en-us.pdf
Question 3
A Storage Administrator is adding an appliance into an existing Dell EMC PowerStore T cluster.
What is different about the management network configuration for the new appliance compared to configuring an initial appliance for the cluster?
- All the needed management IP addresses for the new appliance must be pre-configured on the cluster
- Additional appliance does not require a cluster management IP address
- Additional appliance inherits all its management IPs from the existing appliance
- All the needed management IP addresses for the new appliance are auto-generated by the cluster
Correct answer: D
Question 4
What describes the power requirements for Dell EMC PowerStore?
- Lower model numbered systems require less AC line current than higher model numbered systems
- T models require less total power than X models
- X models require less total power than T models
- Lower model numbered systems require less input voltage (VAC) than higher model numbered systems
Correct answer: A
Explanation:
Reference: https://www.dell.com/support/manuals/pk/en/pkbsd1/powerstore/pwrstr-plang/power-requirements?guid=guid-21e142df-e22c-4bbc-8978-7c6124753654&lang=en-us Reference: https://www.dell.com/support/manuals/pk/en/pkbsd1/powerstore/pwrstr-plang/power-requirements?guid=guid-21e142df-e22c-4bbc-8978-7c6124753654&lang=en-us
Question 5
What is the last step when adding a drive to a Dell EMC PowerStore system?
- Verify the new drive is seen
- Add the drive to the pool
- Backup the keystore
- Zero the drive
Correct answer: A
Explanation:
Reference: https://www.dell.com/support/manuals/pk/en/pkbsd1/powerstore-9000t/pwrstr-isg/install-a-25-drive?guid=guid-bddae51e-a561-4e84-bc0a-c2e99a43f033&lang=en-us Reference: https://www.dell.com/support/manuals/pk/en/pkbsd1/powerstore-9000t/pwrstr-isg/install-a-25-drive?guid=guid-bddae51e-a561-4e84-bc0a-c2e99a43f033&lang=en-us
Question 6
Refer to the exhibit.
A Storage Administrator is troubleshooting a Dell EMC PowerStore T hardware issue. They observe that the base enclosure LED circled is blue. What does this indicate?
- Base enclosure hardware is operating normally
- Base enclosure has a component hardware fault
- Cluster has only a single appliance
- Appliance has a node in service mode
Correct answer: A
Explanation:
Reference: https://www.dell.com/support/manuals/pk/en/pkbsd1/powerstore-9000t/pwrstr-isg/embedded-module-leds?guid=guid-bc07892c-75cf-43b6-8f17-8a4c49001aeb&lang=en-us Reference: https://www.dell.com/support/manuals/pk/en/pkbsd1/powerstore-9000t/pwrstr-isg/embedded-module-leds?guid=guid-bc07892c-75cf-43b6-8f17-8a4c49001aeb&lang=en-us
Question 7
A Storage Administrator needs to connect through SSH to run svc commands. How is the SSH session configured?
- Appliance IP address using port 22
- NAS server IP address using port 26
- NAS server IP address using port 22
- Appliance IP address using port 26
Correct answer: C
Question 8
Which port is used to SSH from one Dell EMC PowerStore appliance to another?
- 22
- 26
- 443
- 21
Correct answer: A
Explanation:
Reference: https://topics-cdn.dell.com/pdf/pwrstr-scg_en-us.pdf Reference: https://topics-cdn.dell.com/pdf/pwrstr-scg_en-us.pdf
Question 9
During Dell EMC PowerStore startup, both appliance nodes have rebooted in service mode. What must be done first to avoid management software conflicts?
- Reboot node B
- Clear the boot mode
- Disable node B boot mode
- Return node A to normal mode
Correct answer: D
Explanation:
Reference: https://www.dell.com/support/manuals/pk/en/pkbsd1/powerstore-1000/pwrstr-isg/power-control-procedure-considerations?guid=guid-4352c94e-0ae7-4a2e-8593-9ae135bb9e34&lang=en-us Reference: https://www.dell.com/support/manuals/pk/en/pkbsd1/powerstore-1000/pwrstr-isg/power-control-procedure-considerations?guid=guid-4352c94e-0ae7-4a2e-8593-9ae135bb9e34&lang=en-us
Question 10
Refer to the exhibit.
What is the result of the network configuration shown for a Dell EMC PowerStore T?
- Interfaces are configured for remote replication traffic
- Interfaces are configured for PowerStore discovery traffic
- Ports 1/1/55 and 1/1/56 are added to a new LACP domain
- Ports 1/1/55 and 1/1/56 are added to the VLTi domain
Correct answer: B
